Do-it-yourself Crafted-In Media IKEA Wall Unit with Extra Storage produced from an IKEA bookcase. Get a develop in seem on a budget and even install it by yourself.
Seeking for extra IKEA hacks? Produce a flat entrance file cupboard built from an IKEA Kallax. Or go for a substantial course IKEA hack seem with these projects. Or gown up a Tarva chest way too.
Howdy, Remodelaholics! I am Tamara again all over again from Provident Household Design where by I share house Do-it-yourself projects and decorating ideas on a budget! I genuinely think you can achieve a journal gorgeous house on even a tiny budget.
I lately turned my kid’s messy basement playroom into an structured, cool kid’s hangout retreat (they actually want to shell out time down there now)!
We wanted extra storage for the little ones toys and a way to disguise a couple of metal beam supports in the completed element of our basement (about two hundred sqft).
Both the mess and the beams were being main eyesores which can be noticed in the picture under!
The alternative to these eyesores was creating a Media Wall Unit with heaps of toy storage! I designed it close to the beams so that they would be concealed killing two birds with one stone!
Media Wall Approach
I was impressed by this media wall technique and definitely appreciate it… see it at Pottery Barn Youngsters (affiliate backlink).
BUT I had no where by in the vicinity of $one,seven-hundred to shell out on it. I did have $one hundred to shell out and which is how substantially it value to make the whole media wall device proven under!
Consider it or not this job begins with two Ikea Gersby Bookcases (only $25 every)!
So let’s start out!
Bookshelves Building Tutorial
Abide by these ways to get this IKEA wall device media center seem.
Construct the Bookshelves
one. Initially, put the Ikea bookcase together adhering to the instructions in the deal (it is very simple). At this level you can go away off the removable shelves.
two. Following, you will start out generating the box element that attaches to the bookcase so you will want to get the box pieces cut.
Beneath are the measurements I utilised for every side of the box (not like the major). I utilised particle board which is very strong but much less high priced than wood.
3. Keep the left side piece of particle board up coming to the bookcase as proven under and with a drill screw a screw into a little piece a wood or MDF so that there is a screw in the particle board and one in the bookcase holding the two with each other. Do one on the major and one on the bottom.
four. Repeat the over action for the correct side particle board part. After the left side and correct side boards are attached it will seem like the picture under.
Optional: If you want your cupboard box to have a bottom now is the time to slide it in as proven over. If not the bottom will just be the ground surface area it is resting on.
five. Following we will be attaching the entrance of the box. We will do this by using L brackets or corner braces on the inside entrance corners of the box.
Idea: Walmart has a genuinely excellent price on their “Corner Braces”. They provide a four-pk. for close to $two (other spots it is $four-$six).
Placement the entrance piece about the sides items and spot a bracket on the inside corner and screw it limited generating sure the corners line up very well.
Repeat on equally sides!
six. Now comes the major of the box which will be how the box opens. This piece will be 24″ x 23″ (I got 24″ x 24″ inch particle items at Household Depot for only $one.28)! The major piece will slide to the again of the bookcase so it will want to be trimmed on the sides as proven under.
I utilised my jig saw to lower the major piece particle board together the lower strains I had built with my ruler and pen.
7. Apply caulk to where by all of the distinct items of wood satisfy.
Now make a different one and then you will have finished the shelves element of the media wall device as proven under.
As you can see over we now want to make “the bench” element of the the media IKEA wall device. I also included an extra shelf to the bookcase but that was just in buy to absolutely disguise the metal beam supports.
I produced the diagram under to assistance you visualize the adhering to ways in creating the bench element. If you get baffled at all you can refer to this diagram for clarification .
Bench Building Tutorial
Making the Foundation of the Bench
Step one- Decide how substantially distance you want involving the two shelving units (most most likely based mostly upon the measurement of your Tv). Measure equally the length and the depth. Using a jigsaw or table noticed lower a piece of particle board to the measurement and spot it on the ground involving the two bookshelves. This is your foundation piece.
Step two- Decide how substantial you want the bench element to be then minus an inch (or the thickness of major of the bench). Cut a piece of particle board the depth of your bench by the the peak you just calculated.
Stand the particle board upright in the center of the foundation piece. Secure the piece upright with four L-Brackets (two on every side of the center piece) connecting the horizontal foundation piece to what we’ll refer to as the divider piece.
Making the Experience of the Bench
Note: I utilised MDF sheeting lower to measurement but you can use wood if you would like.
Step 3- Take a one x four and lower it into two items that are the peak of your bench minus one inch (or the thickness of major of the bench). Place the to start with one standing upright up coming to the left bookshelf. Nail the bottom of it into the foundation piece (from Step one).
Step four- Do the exact same issue with the other 1×4 on the correct side.
Step five- Measure the distance involving the two boards you just installed. Cut two 1×4’s to this measurement. Take one of the boards and spot it involving the two vertical boards you just installed. This board will be placed towards the ground and will be nailed to the foundation piece as very well.
Step six- Place the other board in involving the two vertical side boards so that the tops of the side boards line up seamlessly with it is major Use a amount to make sure it is beautifully horizontal and then nail into spot by nailing it into the entrance stop of the divider piece (from action two)
Secure the major board to the side boards with a connecting piece of wood (nailed on the inside of the bench) and do on equally sides.
See picture under.
Step 7- Measure the distance involving the horizontal bottom and major boards that you just installed in action five and six. Cut a one x four to this length and nail it vertically to the entrance stop of the divider piece.
Making the Major of the Bench
A) Now we will be putting in the assist boards to keep up the major of the Bench. Measure how tall you want the bench to be minus the thickness of the major piece. Draw a line (generating sure it is amount) at this measurement on the sides of equally bookshelves.
Put the major of the assist board (desires to be at minimum an inch thick) together the strains you just drew and nail to the sides of the bookshelves
B) Measure for the major of the bench seat (length and depth). Cut your wood to measurement and spot it on assist boards and is should also rest on major of the Experience of the bench. You can both glue or nail into spot.
Optional- Incorporate trim to your desire. I nailed a piece of trim to the entrance of the major piece of the bench.
I also included a piece of baseboard trim to the bottom entrance of the entire wall device.
Finally, I included a piece of lattice trim to the side again of the bookshelves to disguise the hole involving the shelves and the wall.
And I have thought about introducing attractive pulls to the entrance of the bins but have not uncovered the “right” types nonetheless!:-)
So there you have it! If you have any questions remember to be sure to check with!! We are loving our media wall device and I imagine you will appreciate yours way too (primarily how substantially the storage bins can keep and disguise)!:-)
Pin this publish so you can come across it later on:
Initially posted April 23, 2016 // Up-to-date April 8, 2020