What is a pocket door? And how do you install a pocket door? Understand the recommendations and tricks for installing a pocket door to preserve flooring house from a classic hinged door swing. An great solution for smaller spaces or awkward door locations.
For far more smaller house alternatives, attempt these: Ideas to make a smaller house come to feel open, our Foldable Craft Desk, and a Smaller house research or place of work station.
Right before we show you how to install a pocket door — let’s remedy the most widespread problem:
What is a pocket door?
A pocket door is a sliding door on a observe inside of the wall. Exactly where a sliding barn door and the barn door hardware are on the outside of the wall, a pocket door and pocket door hardware are installed inside of the wall and totally concealed.
Concealed pocket doorways are good alternatives for smaller spaces and half bogs, due to the fact they preserve the flooring house from a classic hinged door swing, while nevertheless supplying far more privateness than a barn door. Pocket doorways are also totally concealed when open, so they really do not need any adjustment to your wall decor either.
Similar Looking at: Diy Barn Doors and Barn Doorway Components
For our pocket door install, we had a half bath at the conclusion of a hallway, with the door swinging out. We required a pocket door! You can see above how the door opened up into the corridor and, with young children, it was just normally open. Across the corridor was our bedroom doorway, so it was blocked and the images on the wall were being only half visible.
Not the glimpse and come to feel we were being going for (in particular with our new board and batten wainscoting close to the home) and it was poor for the going for walks targeted traffic movement, so a pocket door was the way to go for us. I Very advocate a prebuilt pocket door kit and here’s how the method goes:
How To Put in A Pocket Doorway
*Don’t forget, ahead of starting any task that impacts the composition of your residence be sure to check with with a structural engineer or architect!*
Update March 2019: We installed a different pocket door in our recent residence and made a video to show you the method! Verify it out more than on our YouTube channel:
Materials and tools for pocket door body set up
This write-up contains affiliate links. Understand far more and read through our whole disclosure plan right here.
Move 1: Pick the place
This wonderful blank wall with no electrical or plumbing inside of made the best spot for a pocket door.
Move two: Eliminate the present door
Ahh… the variance it will make to just take off the door! The good issue about installing a pocket door is that when you just take off the present door, you can see specifically how the house will come to feel when you are completed: wonderful and open, no door blocking your path!
Move three: Dangle drop cloths
Right before starting any demo, set up some drop cloths to have all. the. dust. (This drop cloth is hung in the room that shares the wall the pocket door is going into.)
Move four: Eliminate drywall
The pocket door will go in the wall that is amongst the half bath and our learn toilet shower, so we reduce out the drywall on the half bath side quite cautiously (We even retained it in one particular piece and reinstalled it! NO waste!). We scored the walls deeply at all the corners, then reduce by means of the other sections and made use of a crowbar to carefully pop the nails out of the back again of the drywall (you can also use a reciprocating saw to reduce the nails to get you begun).
Here is the large piece of drywall as soon as removed…
Move five: Eliminate studs
Next, we eliminated the studs and header where the pocket door kit will go. (We did not make a short-term wall because this home has two parallel walls inside three ft on either side. If you do not have those people supporting walls, you may well require to construct a short-term wall ahead of getting rid of the studs. Check with a contractor, if required.)
We made use of a reciprocating saw to reduce the nails so that the studs could be reused.
Move 6: Establish a door body
Justin begun with a new header, and established the jack and king studs in place. (Jack means the one particular supporting the header and the king is the whole top stud that sits outside the header.)
Move seven: Include the pocket door kit
Now that the door framing is in place, the effortless aspect is incorporating the pocket door kit. Mainly, it is a slot (pocket) with house for the door to slide into and a observe on top.
Use shims to assure it sits in the good place.
Move eight: Prepare the present door, if required.
Include the observe hardware to the present door employing the recommendations that come with the pocket door kit. Also take out the previous door knob and hinges and install a handle plug, if you require one particular.
Move nine: Dangle the door
And the final final results? Pocket door perfection… very well, pretty much!
It reached perfection when we installed all the door trim and a wonderful coat of black paint to match the other doorways!
Glance how open and unobstructed the house is now! I hung new family photos when all the wainscoting and trim was up… like it!)
If you want to see the 1st write-up about the 1/two bath check out it out right here!
You should observe together with us on Pinterest, YouTube, Instagram and Facebook.
And obtain far more good door tutorials, this kind of as:
Printed Aug 22 2012 // Up-to-date Apr twenty 2020